GLASSES – SPECTACLE FRAMES
Brazing alloys for manufacturing of: spectacle frames, hinges for glasses.
All alloys mentioned in the table below are also available as flat wire:
thickness: 0,1 – 0,12 – 0,15 – 0,2 mm
width: 1,2 – 1,3 – 1,5 – 1,7 – 2,0 mm.
Also available as thin wires: diameter starting from 0,3 mm.
Silver Based Alloys
Code | Composition % | Melting Range SOL-LIQ | Density | Tensile strength | Standard | |||||||||
Ag | Cu | Zn | Ni | Mn | Si | Sn | In | °C | g/cm3 | kg/mm2 | ISO 17672 | EN 1044 | AWS A5.8 | |
Alloys |
||||||||||||||
Ag40Ni | 40 | 30 | 28 | 2 | – | – | – | 670-780 | 8,9 | – | Ag 440 | — | BAg-4 | |
Ag40Ni/1 | 40 | 58 | – | 2 | – | – | – | 780-900 | 9,6 | 35 | — | — | — | |
Notes | Alloys suitable for stainless steel in wet conditions. Ag40Ni/1 is also suitable for brazing in oven. | |||||||||||||
Ag44 | 45 | 30 | 26 | – | – | 675-735 | 9,1 | 51 | Ag 244 | AG 203 | — | |||
Ag45Sn | 45 | 27 | 25,5 | – | 2,5 | 640-680 | 9,2 | 43 | Ag 145 | AG 104 | BAg-36 | |||
Ag49MnNi | 49 | 16 | 23 | 4,5 | 7,5 | – | – | 680-705 | 8,9 | 55 | Ag 449 | AG 502 | BAg-22 | |
Notes | For Hard Metal. | |||||||||||||
Ag50Ni | 50 | 20 | 28 | 2 | – | – | – | 660-705 | 9,0 | 45 | Ag 450 | — | BAg-24 | |
Notes | Suitable for stainless steel in wet conditions. | |||||||||||||
Ag55Sn | 55 | 21 | 22 | – | 2 | 630-660 | 9,4 | 44 | Ag 155 | AG 103 | — | |||
Ag56Sn | 56 | 22 | 17 | – | 5 | 620-655 | 9,4 | 48 | Ag 156 | AG 102 | BAg-7 | |||
Ag60 | 60 | 26 | 14 | – | – | 695-730 | 9,5 | 45 | — | AG 202 | — | |||
Ag60Sn | 60 | 23 | 14 | – | 3 | 620-685 | 9,6 | 48 | — | AG 101 | — | |||
Ag72 | 72 | 28 | – | – | – | – | – | 780-780 | 10 | 35 | Ag 272 | AG 401 | BAg-8 | |
Notes | Alloys suitable for brazing in oven. Ag60Sn/1 is also suitable for stainless steel in wet conditions. | |||||||||||||
Fluxes |
||||||||||||||
FLUX AG4 | General purpose – Very wide range of temperatures | |||||||||||||
FLUX AG7 | General purpose. Also for Stainless Steel | |||||||||||||
FLUX AG8 | For Stainless Steel and Hard Metal – Brown Paste |
Copper-Phosphorus Alloys
Code | Composition % | Melting Range SOL-LIQ | Flow point | Density | Tensile strength | Standard | |||||
Ag | Cu | P | Sn | °C | °C | g/cm3 | kg/mm2 | ISO 17672 | EN 1044 | AWS A5.8 | |
Alloys |
|||||||||||
Ag15CuP | 15 | Bal. | 5 | – | 645-800 | 700 | 8,4 | 54 | CuP 284 | CP 102 | BCuP-5 |
Fluxes |
|||||||||||
FLUX AG4 | General purpose – Very wide range of temperatures |